While loading up some 10mm recently I ran into the infamous Glock bulge. Here is a video on the setup and benefits of the Redding G-rx Die with the optional bottle adaptor. Squatch ReloadingThis channel focuses on the guy or gal who is thinking about getting into reloading. There is a lot of information out […]
I’ve seen a lot of videos the last couple years, so I thought I would see what they are about. Thanks for watching treesablowin
Taking a look at the new Tekmat ultra gun cleaning mat. It has some updates over the old style mat. I show you the difference between the two.
Ladder testing some North East Reloading 124gr plated 9mm bullets. We are using CFE Pistol powder from Hodgdon, Starline Brass and CCI primers.
Out shooting some of the TL356-124-2R bullets from a Lee mold that MCK sent out. Thanks for letting me try these MCK!
I tested the 10mm 180 grain Hornady XTP shot from a Glock 20 into ballistics gel. These were loaded with 9.5 grains of Hodgdon Longshot powder.
I’m pretty bad and only shoot and clean my carry gun once a year. How often do you shoot and carry yours?
Today, we talk about what we did with guns this week, a few cool new molds, and talk about what's going on in Connecticut.
Trying out Gallant Bullets with Titegroup powder in my Glock 17 9mm with a Bear Creek arsenal threaded barrel.
I'm an idiot; so, here's a quick video on how to replace the magazine catch on a Foxtrot Mike Products .45 ACP lower. FYI, Foxtrot Mike has awesome customer service!
Assembling two AR pistol lowers. One of the lowers is the Foxtrot Mike Products .45 ACP FM-45 lower receiver, and the other is a "standard" AR-15 lower receiver I picked up from Palmetto State Armory.
Testing out Accura 124gr 9mm bullets with Hodgdon HP38 and Starline Brass in my Glock 17 with a Bear Creek Arsenal Barrel.
A quick look at the Foxtrot Mike Products .45 ACP stripped lower receiver. I do a quick comparison to a "standard" AR-15 lower receiver and cover a few of the similarities and a few of the key differences.
Does a Full Metal Jacket make a Good Penetrating Bear Load? Shooting the Glock 29 vs. Glock 20 vs. Glock 40 with the 165gr FMJ from Underwood.
I was tagged for Everyday Carry Dump
A Review of the Secret Squirrel Kydex Holster for the Glock 29/30 SF.
Today on Kentucky Ballistics we have some fun with the Olight Baldr Pro! I hope you enjoy the video and thanks for watching!
I go through the entire process of casting, powdercoating, loading, and shooting some hard cast round nose bullets using the high quality NOE bullet mold for my 10mm handguns. I had wanted a round nose bullet for 10mm plinking loads. Something that would feed simply and flawlessly in each of my 10mm handguns and carbines. This bullet mold seems to do the trick.
Had a viewer request from Uncle Jim to see if hollow points would feed through my Bear Creek Arsenal Glock 17 threaded barrel. This Bear Creek Arsenal Glock barrel has been a great barrel so far.
Trying out Magpul Glock 17 & 12 round mags with different ammo.
Testing out the ETS clear mags for Glocks with different ammo.
Check to see if a Ghost connector drops the pounds of the trigger pull.
Testing out the Jagemann Sporting Group Glock 17 mags.
In this episode, Jason and Taco talk about a new Glock 34 MOS Gen 5 for a bit and compare it with a Walther PPQ. They also talk about a couple AR15 builds and revisit the topic of bump-in-the-night guns and trunk guns. Taco introduces the world to the "Pirate ARRRRR pistol."